Search the database of auto parts codes

     

     

     

     

     

    previous

    Page 44 - Catalog spare parts BPW brake disc
    P. 44
    Catalogs auto parts for car and truck

    AUTO PARTS

    Page 44 - Catalog spare parts BPW brake disc

    Auto Parts / BPW-EL-TSB 31231601e                                                                               Page 43
                                                                       Hubs, hub bearings                          4
    
    
                                                               Grease filling, bearing adjustment                 4.6
    
                                                             ECO Plus 2 Hub system (ECO Plus 2 Unit)
    
    
            Grease filling per wheel hub                        ECO Plus 2 hub system (ECO Plus 2 Unit)
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
    
            The ECO Plus 2 hub system is designed for the use of longlife grease. On expiry of the guarantee, the roller bearings, the inside
            of the hub and the seals are to be thoroughly cleaned (with diesel oil), dried, checked to see if they can be re-used; and re-greased
            every three years when used off-road, or every 5 years when used on the road, within Europe (or every year when off-road and every
    
    
            two years when on the road outside of Europe) (observe the current BPW maintenance instructions).
            Apply BPW ECO-Assembly and Protection Spray as thin as possible and around the entire area of bearing seats of the axle stub.
                                                  BPW longlife roller bearing grease ECO-Li Plus ,
                                                  Quantity per tapered roller bearing
                                                                1  inner                          2  outer
            Axle load        Axle type              Roller bearings     Quantity      Roller bearings     Quantity
                             SH.. 8 - 9t ECO Plus 2
            8000 - 9000kg                               33118            130 g            33213            90 g
                             SK.. 8 - 9t ECO Plus 2
              1   Clean the grease cartridge and fi ll it on both sides up to the edge with BPW longlife roller bearing grease ECO-Li Plus .
              +   Apply a ring-shaped bead of grease to the running surfaces of the outer bearing races.
              2   Apply a coat of BPW longlife roller bearing grease ECO-Li Plus  all around the lip of the seal.
            For other procedures see the current maintenance instructions.
            When BPW grease applicators are used there is no need to fi ll the grease cartridge or to apply the bead of grease.
            Greasing with grease spray see page 42.
    
            Bearing adjustment                                 ECO Plus 2 hub system (ECO Plus 2 Unit)
              1.  Undo the hub cap by turning it through approx. 30 degrees in an anticlockwise direction (see page 34).
                  When turned further the hub cap lifts clearly away from the ECO unit and can be removed by pulling it away.
              2.  Remove the hooked spring ring and retaining key from the axle bolt.
              3.  Tighten the axle bolt while at the same time turning the ECO unit with a 46 mm hexagon spanner until the
                  crown of the axle bolt clicks round.
                  NB! Do not use an impact driver.
              4.  Insert the retaining key into the recess in the axle bolt and into the crown of the toothed lock washer
                  (do not turn the axle bolt back).
              5.  Insert the hooked spring ring into the groove at the end of the hexagon profi le of the axle bolt.
              6.  Insert a new ‘O’-ring into the groove in the wheel hub.
              7.  Apply a thin layer of BPW longlife roller bearing grease ECO-Li Plus  to the hub cap in the area of the O-ring contact
                  surface and the bayonet fi tting.
              8.  Put the hub cap on (position 1, page 34). Use the 120 mm hub cap spanner to lock the hub cap in place by
                  turning it through approx. 30 degrees in a clockwise direction, while at the same time pressing on the hub cap.
                  It is fi rmly in place when it reaches position 2 (page 34).
                  NB! Do not use an impact driver - bayonet fi tting.
    
    
    
                                    
    previous
       39   40   41   42   43   44   45   46   47   48   49
    Current Page
    next

     

     

     

     

     

    next