Search the database of auto parts codes

     

     

     

     

     

    previous

    Page 85 - Catalog spare parts BPW HKN
    P. 85
    Catalogs auto parts for car and truck

    AUTO PARTS

    Page 85 - Catalog spare parts BPW HKN

    Auto Parts / BPW-EL-HKN 31021701e                                                                               Page 85
    
                                                                           Hubs, hub bearings                          5
    
    
                H.. / K.. / N..                Grease filling per wheel hub, bearing adjustment                       5.3
    
                                                                 ECO Plus 2 hub system (ECO Plus 2 Unit)            5.3.2
    
    
                 Grease filling per wheel hub                                 ECO Plus 2 hub system (ECO Plus 2 Unit)
                                                                                                                            H
    
    
    
    
                                                  1                             2                                           K
                                               130 g                           90 g
                                                                                                                            N
    
    
    
    
    
    
    
    
    
    
                 The ECO Plus 2 hub system is designed for the use of longlife grease. On expiry of the guarantee, the roller bearings, the inside of the hub and
                 the seals are to be thoroughly cleaned (with diesel oil), dried, checked to see if they can be re-used; and regreased every three years when
                 used off-road, or every 5 years when used on the road, within Europe (or every year when off-road and every two years when on the road
                 outside of Europe) (observe the current BPW maintenance instructions).
                 Apply BPW ECO Protection Grease as thin as possible and around the entire area of bearing seats of the axle stub.
                                                      BPW longlife roller bearing grease ECO-Li Plus ,
                                                      quantity per tapered roller bearing
                                                                    1  inner                          2  outer
                 Axle load        Axle type              Roller bearing     Quantity       Roller bearing     Quantity
                                  H.. 6.5 - 9t ECO Plus 2
                 6500 - 9000kg    K.. 8 - 9t ECO Plus 2     33118            130 g            33213             90 g
                                  N.. 7 - 9t ECO Plus 2
                  1   Clean the grease cartridge and fill it on both sides up to the edge with BPW ECO-Li Plus  special long-life grease.
                  +   Apply a ring-shaped bead of grease to the running surfaces of the outer bearing races.
                  2   Apply a coat of BPW ECO-Li Plus  special long-life grease all around the lip of the seal.
                 For other procedures see the current maintenance instructions (BPW-W-ECO Plus 1203...e).
                 When BPW grease applicators are used there is no need to fill the grease cartridge or to apply the bead of grease.
                 Greasing with grease spray see page 87.
    
                 Bearing adjustment                                           ECO Plus 2 hub system (ECO Plus 2 Unit)
                  1.  Undo the hub cap by turning it through approx. 30 degrees in an anticlockwise direction (see page 59).
                      When turned further the hub cap lifts clearly away from the ECO unit and can be removed by pulling it away.
                  2.  Remove the hooked spring ring and retaining key from the axle bolt.
                  3.  Tighten the axle bolt while at the same time turning the ECO unit with a 46 mm hexagon spanner until the
                      crown of the axle bolt clicks round.
                      NB! Do not use an impact driver.
                  4.  Insert the retaining key into the recess in the axle bolt and into the crown of the toothed lock washer (do not
                      turn the axle bolt back)..
                  5.  Insert the hooked spring ring into the groove at the end of the hexagon profile of the axle bolt.
                  6.  Insert a new O-ring into the groove in the wheel hub.
                  7.  Apply a thin layer of BPW ECO-Li  Plus  special longlife grease to the hub cap in the area of the O-ring contact
                      surface and the bayonet fitting.
                  8.  Put the hub cap on (position 1, page 59). Use the 120 mm hub cap spanner to lock the hub cap in place by
                      turning it through approx. 30 degrees in a clockwise direction, while at the same time pressing on the hub cap.
                      It is firmly in place when it reaches position 2 (page 59).
                      NB! Do not use an impact driver - bayonet fitting.
    
    
    
                                    
    previous
       80   81   82   83   84   85   86   87   88   89   90
    Current Page
    next

     

     

     

     

     

    next